Magpro2 X17 Clone Password Will Be

No: IT06830930829 R.E.A. PA-419009 Registered Capital 1.500.000,00 i.e. GET SOCIAL 2020 MAGICMOTORSPORT.

Remember Me FORGOT YOUR PASSWORD FORGOT YOUR DETAILS USERNAME OR EMAIL AAH, WAIT, I REMEMBER NOW English Italiano Franais Deutsch Espaol polski HOME PRODUCTS Flex DynoRoad StageX dynoMAG Power Catalog MAGPro2 ABOUT US Team Power Division Careers Photo Gallery History page Trade Show Calendar TRAINING SHOP NEWSLETTER Software Updates Events Info and Communication CONTACT US Send us a claim MMS HELPDESK Customer Area Home Newsletter Updates Flex v2.00.00 released March 27, 2021 BLOG Gossip Monday, 12 November 2018 Published in Updates Flex v2.00.00 released Please note you will need last version of one of the following browsers to run Flex: Google Chrome (recommended) Mozilla Firefox Microsoft Edge The following browser will have incompatibility with our software and should never be used to work on a control unit: Internet Explorer (any version) Once installed, just launch Flex.exe, then connect Flex by USB to your PC and Flex will automatically start in your default browser.

For your comfort, we highlighted the new protocols which are not present in X17.

For each of the migrated protocols from X17 to Flex there are improvements, though, thus we advise you to have a careful read at the following general explanation before looking at the release list: The new protocols added can be divided in two groups: NEW Bench for Tricore based ECUs: What is that: those protocols allow full read and full write of the ECU, including each of the memories stored inside the engine control unit without any encryption.

How does it work: This protocol is completely different from any other bootloader mode on the market.

Tuning, clone, bypassing security and restoring backup are no issue at all and you dont even need to bother opening the ECU Furthermore, its done so it bypasses any TPROT level till now, including those previously doable only by sending ECU to MMS Office.

Password is stored online, so it will not be any longer needed to keep it as a backup.

Magpro2 X17 Clone Password Will Be

After first reading, which is done automatically by Flex, password will be always downloaded by server for each access, reducing the amount of time needed to work.

How much does it take: Reading times have been tested from 3 to 6 minutes in total, depending on ECU model.

Writing times depend on actual size of modification inside file, from few seconds to about 9 minutes.

Which module do I need to buy: if you are a previous owner of MAGP1.18 Bosch Tricore Unlock plugin (and a T-BOOT or X17), this new protocol is totally free of charge.

Who havent purchased MAGP1.18 but has got a T-BOOT or X17 can contact Sales Department to purchase this protocol.

For anyone else, it is included in our FULL Bench MEDC17BL TRICORE module at 1800 VAT.

Boot for Tricore based ECUs What is that: those protocols allow full read and full write of the ECU, including each of the memories stored inside the engine control unit without any encryption.

What is different from X17: This protocol bypasses any TPROT level till now, including those previously doable only by sending ECU to MMS Office.

How much does it take: Reading times have been tested from 4 to 7 minutes in total, depending on ECU model.

Writing times depend on actual size of modification inside file, from few seconds to about 10 minutes.

Which module do I need to buy: if you are a previous owner of MAGP1.18 Bosch Tricore Unlock plugin (and a T-BOOT or X17), its totally free of charge.

New units will be added to each release.

You can click here to review the full list of supported vehicles by Full Bench MEDC17 Software package.

No: IT06830930829 R.E.A.

PA-419009 Registered Capital 1.500.000,00 i.e.

GET SOCIAL 2020 MAGICMOTORSPORT.